관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Fibre-reinforced plastics — Methods of producing test plates — Part 1: General conditions
| 분야 | ISO/TC 61/SC 13 : Composites and reinforcement fibres |
|---|---|
| 적용범위 | The various parts of ISO 1268 (see the foreword) describe methods used to prepare reinforced-plastics plates from which test specimens can be cut. This allows the properties of a composite, or the constituents of the composite, to be determined. The methods are intended to cover all the main types of reinforcement and resin matrix. The choice of test plate preparation method depends on: a) the reinforcement: its nature (glass, carbon, aramid, etc.); its form (roving, mat, woven fabric, etc.); its orientation with respect to the length, width and thickness of the plate; its content in the reinforced plastic; b) the matrix (thermosetting or thermoplastic); c) the magnitude expected for the properties; d) the production process that is to be evaluated. Since the mechanical properties of a reinforced plastic are known to be dependent on the process by which the plastic is produced, it is recommended that the test plates be prepared, if possible, by the same method that will be used to produce the plastic. This part of ISO 1268 describes the general requirements common to all the methods. |
| 국제분류(ICS)코드 | 83.120 : 강화 플라스틱 |
| 페이지수 | 4 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 1268-1:2001 | Fibre-reinforced plastics — Methods of producing test plates — Part 1: General conditions | 2001-12-06 | 표준 |
ISO 1268-3:2000 - Fibre-reinforced plastics — Methods of producing test plates — Part 3: Wet compression moulding 상세보기
ISO 1268-2:2001 - Fibre-reinforced plastics — Methods of producing test plates — Part 2: Contact and spray-up moulding 상세보기
ISO 1268-7:2001 - Fibre-reinforced plastics — Methods of producing test plates — Part 7: Resin transfer moulding 상세보기
ISO 1268-5:2001 - Fibre-reinforced plastics — Methods of producing test plates — Part 5: Filament winding 상세보기
ISO 1268-6:2002 - Fibre-reinforced plastics — Methods of producing test plates — Part 6: Pultrusion moulding 상세보기
ISO 12686:1999 - Metallic and other inorganic coatings -- Automated controlled shot-peening of metallic articles prior to nickel, autocatalytic nickel or chromium plating, or as a final finish 상세보기
ISO 5725-5:1998 - Accuracy (trueness and precision) of measurement methods and results -- Part 5: Alternative methods for the determination of the precision of a standard measurement method 상세보기
DIN EN 13473-3:2001-11 - Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 3: Specific requirements; English version of DIN EN 13473-3 상세보기
DIN EN 13473-2:2001-11 - Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 2: Methods of test and general requirements; English version of DIN EN 13473-2 상세보기
DIN EN 13473-1:2001-11 - Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 1: Designation; English version of DIN EN 13473-1 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
