관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method
| 분야 | ISO/TC 108 : Mechanical vibration, shock and condition monitoring |
|---|---|
| 적용범위 | ISO 18437-3:2005 defines a cantilever shear beam method for determining from laboratory measurements the dynamic mechanical properties of the resilient materials used in vibration isolators. Common errors due to clamping the specimen are avoided by using fixed ends so there is no rotational motion of the beam at its ends. This part of ISO 18437 is applicable to shock and vibration systems operating from a fraction of a hertz to about 20 kHz. ISO 18437-3:2005 is applicable to resilient materials that are used in vibration isolators in order to reduce -- transmissions of unwanted vibrations from machines, structures or vehicles that radiate sound (fluid-borne, airborne, structure-borne, or other), and -- the transmission of low- frequency vibrations that act upon humans or cause damage to structures or sensitive equipment when the vibration is too severe. The data obtained with the measurement methods that are outlined in ISO 18437-3:2005 are used for -- the design of efficient vibration isolators, -- the selection of an optimum material for a given design, -- the theoretical computation of the transfer of vibrations through isolators, -- information during product development, -- product information provided by manufacturers and suppliers, and -- quality control. |
| 국제분류(ICS)코드 | 17.160 : 진동. 충격 및 진동측정 |
| 페이지수 | 14 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 18437-3:2005/Amd 1:2010 | Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method — Amendment 1 | 2010-09-16 | 표준 |
| 2 | ISO 18437-3:2005 | Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method | 2005-04-18 | 표준 |
ISO 18437-2:2005 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 2: Resonance method 상세보기
ISO 18437-4:2008 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 4: Dynamic stiffness method 상세보기
ISO 18437-2:2005/Amd 1:2010 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 2: Resonance method — Amendment 1 상세보기
ISO 18437-3:2005/Amd 1:2010 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method — Amendment 1 상세보기
ISO 18437-5:2011 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 5: Poisson ratio based on comparison between measurements and finite element analysis 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
