관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
폐지
판매
Reciprocating internal combustion engines — Exhaust emission measurement — Part 11: Test-bed measurement of gaseous and particulate exhaust emissions from engines used in nonroad mobile machinery under transient test conditions
| 분야 | ISO/TC 70/SC 8 : Exhaust gas emission measurement |
|---|---|
| 적용범위 | ISO 8178-11:2006 specifies the measurement and evaluation methods for gaseous and particulate exhaust emission from reciprocating internal combustion (RIC) engines under transient conditions on a test bed, necessary for determining one value for each exhaust gas pollutant. The specific transient test cycle covered by ISO 8178-11:2006 is applicable to compression-ignition engines for mobile use with a power output between 37 kW and 560 kW, excluding engines for motor vehicles primarily designed for road use. ISO 8178-11:2006 may be applied to engines used in off-road vehicles and diesel powered off-road industrial equipment as described in ISO 8178-4. This includes, for example, engines for construction equipment including wheel loaders, bulldozers, crawler tractors, crawler loaders, truck-type loaders, off-highway trucks, hydraulic excavators, agricultural equipment, self propelled agricultural vehicles (including tractors), forestry equipment, fork lift trucks, road maintenance equipment and mobile cranes. Many of the procedures described below are detailed accounts of laboratory methods, since determining an emissions value requires performing a complex set of individual measurements, rather than obtaining a single measured value. Thus, the results obtained depend as much on the process of performing the measurements as they depend on the engine and test method. |
| 국제분류(ICS)코드 |
27.020 : 내연기관
13.040.50 : 수송 배기가스 방사 |
| 페이지수 | 71 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 8178-11:2006 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 11: Test-bed measurement of gaseous and particulate exhaust emissions from engines used in nonroad mobile machinery under transient test conditions | 2006-03-29 | 폐지 |
ISO 8178-10:2002 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 10: Test cycles and test procedures for field measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions 상세보기
ISO 8178-7:2015 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 7: Engine family determination 상세보기
ISO 8178-8:2015 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 8: Engine group determination 상세보기
ISO 8178-6:2018 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 6: Report of measuring results and test 상세보기
ISO 8178-3:2019 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 3: Test procedures for measurement of exhaust gas smoke emissions from compression ignition engines using a filter type smoke meter 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
