관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Guidelines for in-service inspections for primary coolant circuit components of light water reactors — Part 1: Mechanized ultrasonic testing
| 분야 | ISO/TC 85/SC 6 : Reactor technology |
|---|---|
| 적용범위 | This document gives guidelines for pre-service-inspections (PSI) and in-service inspections (ISI) with mechanized ultrasonic test (UT) devices on components of the reactor coolant circuit of light water reactors. This document is also applicable on other components of nuclear installations. Mechanized ultrasonic inspections are carried out in order to enable an evaluation in case of — fault indications (e.g. on austenitic weld seams or complex geometry), — indications due to geometry (e.g. in case of root concavity), — complex geometries (e.g. fitting weld seams), or — if a reduction in the radiation exposure of the test personnel can be attained in this way. Ultrasonic test methods are defined for the validation of discontinuities (volume or surface open), requirements for the ultrasonic test equipment, for the preparation of test and device systems, for the implementation of the test and for the recording. This document is applicable for the detection of indications by UT using normal-beam probes and angle-beam probes both in contact technique. It is to be used for UT examination on ferritic and austenitic welds and base material as search techniques and for comparison with acceptance criteria by the national referencing nuclear safety standards. Immersion technique and techniques for sizing are not in the scope of this document and are independent qualified. NOTE Data concerning the test section, test extent, inspection period, inspection interval and evaluation of indications is defined in the applicable national nuclear safety standards. Unless otherwise specified in national nuclear safety standards the minimum requirements of this document are applicable. This document does not define: — extent of examination and scanning plans; — acceptance criteria; — UT techniques for dissimilar metal welds and for sizing (have to be qualified separately); — immersion techniques; — time-of-flight diffraction technique (TOFD). It is recommended that UT examinations are nearly related to the component, the type and size of defects to be considered and are reviewed in specific national inspection qualifications. |
| 국제분류(ICS)코드 | 27.120.10 : 원자로 공학 |
| 페이지수 | 33 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 20890-1:2020 | Guidelines for in-service inspections for primary coolant circuit components of light water reactors — Part 1: Mechanized ultrasonic testing | 2020-06-12 | 표준 |
ISO/DIS 20890-6.2 - Guidelines for in-service inspections for primary coolant circuit components of light water reactors — Part 6: Radiographic testing 상세보기
ISO 20890-2:2020 - Guidelines for in-service inspections for primary coolant circuit components of light water reactors — Part 2: Magnetic particle and penetrant testing 상세보기
ISO 20890-3:2020 - Guidelines for in-service inspections for primary coolant circuit components of light water reactors — Part 3: Hydrostatic testing 상세보기
ISO 20890-4:2020 - Guidelines for in-service inspections for primary coolant circuit components of light water reactors — Part 4: Visual testing 상세보기
ISO 20890-5:2020 - Guidelines for in-service inspections for primary coolant circuit components of light water reactors — Part 5: Eddy current testing of steam generator heating tubes 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
