관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Gears — Calculation of load capacity of worm gears
| 분야 | ISO/TC 60/SC 1 : Nomenclature and wormgearing |
|---|---|
| 적용범위 | This document specifies formulae for calculating the load capacity of cylindrical worm gears and covers load ratings associated with wear, pitting, worm deflection, tooth breakage and temperature. Scuffing and other failure modes are not covered by this document. The load rating and design procedures are only valid for tooth surface sliding velocities, , less than or equal to 25 m/s and contact ratios greater than 2,1. For wear, load rating and design procedures are only valid for tooth surface sliding velocities which are above 0,1 m/s. The rules and recommendations for the dimensioning, lubricants or materials selected by this document only apply to centre distances of 50 mm and larger. For centre distances below 50 mm, method A applies. The choice of appropriate methods of calculation requires knowledge and experience. This document is intended for use by experienced gear designers who can make informed judgements concerning factors. It is not intended for use by engineers who lack the necessary experience. See 4.7. WARNING — The geometry of worm gears is complex, therefore the user of this document is encouraged to make sure that a valid working geometry has been established. |
| 국제분류(ICS)코드 | 21.200 : 기어류 |
| 페이지수 | 88 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO/TS 14521:2020 | Gears — Calculation of load capacity of worm gears | 2020-04-14 | 표준 |
| 2 | ISO/TR 14521:2010 | Gears — Calculation of load capacity of wormgears | 2010-11-11 | 구판 |
관련상품이 존재하지 않습니다.
VDI 2230 Blatt 1:2015-11 - Systematic calculation of highly stressed bolted joints - Joints with one cylindrical bolt 상세보기
JIS B 2709-1 - Helical torsion springs -- Part 1: Basic calculation methods 상세보기
BS 7608:2014+A1:2015 - Guide to fatigue design and assessment of steel products. 상세보기
ISO 2162-1:1993 - Technical product documentation — Springs — Part 1: Simplified representation 상세보기
ISO 2162-2:1993 - Technical product documentation — Springs — Part 2: Presentation of data for cylindrical helical compression springs 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
