관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
| 분야 | 02.01 : 동 및 동합금 |
|---|---|
| 적용범위 | 1.1 This test method establishes the requirements for the expansion pin test for copper and copper-alloy pipe and tubing in sizes up to and including 4 in. (102 mm) in outside diameter. Note 1—For tubes of sizes greater than 4 in. in outside diameter, the following flattening test, as described in the various pipe and tube specifications, is recommended as a substitute for the pin expansion test. For pipe and tubes over 4 in. in outside diameter in the annealed condition, a 4-in. long shall be cut from the end of one of the tubes. This 4-in. long sample shall be flattened so that a gage set at three times the wall thickness will pass over the pipe freely throughout the flattened part. The pipe or tube so tested shall develop no cracks or flaws visible to the unaided eye as a result of this test. In making the flattening test, the elements shall be slowly flattened by one stroke of the press.Note 2—The term "unaided eye," as used herein, permits the use of corrective lenses necessary to obtain normal vision. 1.2 The values stated in inch-pound units are to be regarded as the standard. SI values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 2 |
| Edition | 91(2003) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM B153-22 | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 2022-05-01 | 표준 |
| 2 | ASTM B153-22 REDLINE | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 2022-05-01 | 표준 |
| 3 | ASTM B153-11(2017) | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 2017-04-01 | 구판 |
| 4 | ASTM B153-11 | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 2011-01-01 | 구판 |
| 5 | ASTM B153-05 | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 2005-10-01 | 구판 |
| 6 | ASTM B153-91(2003)e1 | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 2003-04-10 | 구판 |
| 7 | ASTM B153-91(2003) | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 2003-04-10 | 구판 |
| 8 | ASTM B153-91(1996)e1 | Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing | 1996-01-01 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
