관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles
| 분야 | 05.06 : 기체화 연료; 석탄 및 코커스 |
|---|---|
| 적용범위 | 1.1 This test method covers and is suitable for determining the resistance of extruded catalysts and catalyst carriers to compressive force from the side. 1.2 This test method was developed using extruded catalyst and catalyst carriers from 1/16to 1/8 in. in diameter (0.159 to 0.318 cm) and limited to pieces with a length to diameter ratio greater than or equal to 1:1. This test method may be applicable to other diameters. 1.3 This test method is suitable for the determination of mean crush strength per millimetre in the range of 0 to 15 lbf/mm (0 to 65 N/mm). 1.4 The values stated in pounds lbf/mm units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 3 |
| Edition | 03 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D6175-24 | Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles | 2024-09-01 | 표준 |
| 2 | ASTM D6175-24 REDLINE | Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles | 2024-09-01 | 표준 |
| 3 | ASTM D6175-03(2019) | Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles | 2019-04-01 | 구판 |
| 4 | ASTM D6175-03(2013) | Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles | 2013-03-01 | 구판 |
| 5 | ASTM D6175-03(2008) | Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles | 2008-04-01 | 구판 |
| 6 | ASTM D6175-03 | Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles | 2003-10-01 | 구판 |
| 7 | ASTM D6175-98 | Standard Test Method for Radial Crush Strength of Extruded Catalyst Particles | 1998-04-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
