관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 08.03 : 플라스틱 (Ⅲ) |
---|---|
적용범위 | 1.1 This specification provides for the identification of polyethylene plastics molding and extrusion materials in such a manner that the supplier and the user can agree on the acceptability of different commercial lots or shipments. The tests involved in this specification are intended to provide information for identifying materials in accordance with the groups, classes, and grades covered. It is not the function of this specification to provide specific engineering data for design purposes. 1.2 Other requirements may be necessary to identify particular characteristics important to specialized applications. These shall be agreed upon between the user and the supplier, by using the suffixes given in Section 1.3. 1.3 Ethylene plastic materials, being thermoplastic, are reprocessable and recyclable (see Note 1). This specification allows for the use of those ethylene plastic materials, provided that any specific requirements as governed by the producer and the end user are met. Note 1—See Guide D 5033 for information and definitions related to recycled plastics. 1.4 The values stated in SI units are regarded as the standard. 1.5 The following precautionary caveat pertains to the test method portion only, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 For information regarding plastic pipe materials see Specification D 3350. For information regarding wire and cable materials, see Specification D 1248. For information on polyethylenes with densities below 0.910 g/cm3, see Classification D 5593. Note 2—There is no similar or equivalent ISO standard. |
국제분류(ICS)코드 | |
페이지수 | 7 |
Edition | 04 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D4976-12a(2020) | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2020-12-01 | 표준 |
2 | ASTM D4976-12a REDLINE | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2012-08-01 | 표준 |
3 | ASTM D4976-12a | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2012-08-01 | 표준 |
4 | ASTM D4976-12 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2012-04-01 | 구판 |
5 | ASTM D4976-06 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2006-11-15 | 구판 |
6 | ASTM D4976-04a | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2004-12-01 | 구판 |
7 | ASTM D4976-04 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2004-05-01 | 구판 |
8 | ASTM D4976-02e1 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2002-12-10 | 구판 |
9 | ASTM D4976-02 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2002-12-10 | 구판 |
10 | ASTM D4976-00b | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials | 2000-11-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기