관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus
| 분야 | 03.02 : 마모 및 침식;금속 부식 |
|---|---|
| 적용범위 | 1.1 This test method covers laboratory procedures for determining the resistance of metallic materials to scratching abrasion by means of the dry sand/rubber wheel test. It is the intent of this test method to produce data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions. 1.2 Abrasion test results are reported as volume loss in cubic millimetres for the particular test procedure specified. Materials of higher abrasion resistance will have a lower volume loss. Note 1: In order to attain uniformity among laboratories, it is the intent of this test method to require that volume loss due to abrasion be reported only in the metric system as cubic millimetres. 1 mm3 = 6.102 × 10−5 in3. 1.3 This test method covers five recommended procedures which are appropriate for specific degrees of wear resistance or thicknesses of the test material. 1.3.1 Procedure A—This is a relatively severe test which will rank metallic materials on a wide volume loss scale from low to extreme abrasion resistance. It is particularly useful in ranking materials of medium to extreme abrasion resistance. 1.3.2 Procedure B—A short-term variation of Procedure A. It may be used for highly abrasive resistant materials but is particularly useful in the ranking of medium- and low-abrasive-resistant materials. Procedure B should be used when the volume–loss values developed by Procedure A exceeds 100 mm3. 1.3.3 Procedure C—A short-term variation of Procedure A for use on thin coatings. 1.3.4 Procedure D—This is a lighter load variation of Procedure A which is particularly useful in ranking materials of low-abrasion resistance. It is also used in ranking materials of a specific generic type or materials which would be very close in the volume loss rates as developed by Procedure A. 1.3.5 Procedure E—A short-term variation of Procedure B that is useful in the ranking of materials with medium- or low-abrasion resistance. 1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 14 |
| Edition | 16 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM G65-16(2021) | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2021-11-01 | 표준 |
| 2 | ASTM G65-16e1 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2016-03-01 | 구판 |
| 3 | ASTM G65-16 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2016-03-01 | 구판 |
| 4 | ASTM G65-15 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2015-11-01 | 구판 |
| 5 | ASTM G65-04(2010) | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2010-12-01 | 구판 |
| 6 | ASTM G65-04 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2004-11-01 | 구판 |
| 7 | ASTM G65-00 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2000-10-10 | 구판 |
| 8 | ASTM G65-00e1 | Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus | 2000-10-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
