관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Design Loads and Conditions
| 분야 | 15.09 : 종이, 회사 이미지용 상품 |
|---|---|
| 적용범위 | 1.1 This specification addresses the airworthiness requirements for the design loads and conditions of small airplanes. 1.2 This specification is applicable to small airplanes as defined in the F44 terminology standard. Use of the term airplane is used throughout this specification and will mean “small airplane.” 1.3 The applicant for a design approval must seek individual guidance from their respective CAA body concerning the use of this standard as part of a certification plan. For information on which CAA regulatory bodies have accepted this standard (in whole or in part) as a means of compliance to their Small Airplane Airworthiness Rules (hereinafter referred to as “the Rules”), refer to ASTM F44 webpage (www.ASTM.org/COMMITTEE/F44.htm) which includes CAA website links. 1.4 Units—Currently there is a mix of SI and Imperial units. In many locations, SI units have been included otherwise units are as they appear in Amendment 62 of 14 CFR Part 23. In a future revision values will be consistently stated in SI units followed by Imperial units in square brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 28 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F3116/F3116M-23a | Standard Specification for Design Loads and Conditions | 2023-10-01 | 표준 |
| 2 | ASTM F3116/F3116M-23a REDLINE | Standard Specification for Design Loads and Conditions | 2023-10-01 | 표준 |
| 3 | ASTM F3116/F3116M-23 | Standard Specification for Design Loads and Conditions | 2023-03-15 | 구판 |
| 4 | ASTM F3116/F3116M-23 REDLINE | Standard Specification for Design Loads and Conditions | 2023-03-15 | 구판 |
| 5 | ASTM F3116/F3116M-18e1 | Standard Specification for Design Loads and Conditions | 2018-11-01 | 구판 |
| 6 | ASTM F3116/F3116M-18e2 | Standard Specification for Design Loads and Conditions | 2018-11-01 | 구판 |
| 7 | ASTM F3116/F3116M-18 REDLINE | Standard Specification for Design Loads and Conditions | 2018-11-01 | 표준 |
| 8 | ASTM F3116/F3116M-18 | Standard Specification for Design Loads and Conditions | 2018-11-01 | 표준 |
| 9 | ASTM F3116/F3116M-15 | Standard Specification for Design Loads and Conditions | 2015-05-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM F3153-15 - Standard Specification for Verification of Avionics Systems 상세보기
ASTM F2241-14 - Standard Specification for Continued Airworthiness System for Powered Parachute Aircraft 상세보기
ASTM F2316-12(2014) - Standard Specification for Airframe Emergency Parachutes 상세보기
ASTM F2244-14 - Standard Specification for Design and Performance Requirements for Powered Parachute Aircraft 상세보기
ASTM F2506-13 - Standard Specification for Design and Testing of Light Sport Aircraft Propellers (Withdrawn 2022) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
