관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 08.02 : 플라스틱 (Ⅱ) |
---|---|
적용범위 | 1.1 This classification system covers nylon materials suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding and application from solution. 1.2 The properties included in this classification system are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section 5. 1.3 This classification system and subsequent line call-out (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: There is no known ISO equivalent to this standard. Note 2: This classification system is being revised to include international 4-mm specimens and test procedures as the standard for compliance. The 3.2-mm specimens; test methods; and Tables PA, A, and B are included in Appendix X3 as a reference for those wishing to use them. It is recommended that the material manufacturer be consulted on all call-outs against this classification system. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | 83.080.20 : 열가소성 수지재 |
페이지수 | 17 |
Edition | 13(2019) |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D4066-13(2019) | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 2019-11-01 | 표준 |
2 | ASTM D4066-13 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 2013-07-01 | 구판 |
3 | ASTM D4066-01a(2008) | Standard Classification System for Nylon Injection and Extrusion Materials (PA) (Withdrawn 2012) | 2008-09-15 | 구판 |
4 | ASTM D4066-00 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 2001-08-10 | 구판 |
5 | ASTM D4066-01 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 2001-08-10 | 구판 |
6 | ASTM D4066-00a | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 2001-08-10 | 구판 |
7 | ASTM D4066-01a | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 2001-08-10 | 구판 |
8 | ASTM D4066-94b | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 1994-01-15 | 구판 |
9 | ASTM D4066-96ae1 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 구판 | |
10 | ASTM D4066-96 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) | 구판 |
관련상품이 존재하지 않습니다.
ASTM D6778-20 - Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) 상세보기
2023년 KS핸드북-비철 상세보기
KS B ISO 13920 - 용접 — 용접 구조물의 일반 공차 — 길이와 각도 치수 — 모양과 위치 상세보기
ASTM A747/A747M-23 - Standard Specification for Steel Castings, Stainless, Precipitation Hardening 상세보기
2024년 KS핸드북-철강(세트)(set) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기