관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 04.06 : 보온, 방음 |
---|---|
적용범위 | 1.1?This test method covers two procedures for determining the compressive resistance of thermal insulations. 1.1.1?Procedure A covers thermal insulations having an approximate straight-line portion of a load-deformation curve, with or without an identifiable yield point as shown in Figs. 1 and 2. Such behavior is typical of most rigid board or block-type insulations. FIG. 1?Procedure A?Straight Line Portion with Definite Yield Point ![]() FIG. 2?Procedure A?Straight Line Portion but no Definite Yield Point ![]() 1.1.2?Procedure B covers thermal insulations that become increasingly more stiff as load is increased, as shown in Fig. 3. Such behavior is typical of fibrous batt and blanket insulations that have been compressed previously to at least the same deformation by compression packaging or mechanical softening. FIG. 3?Procedure B?Increasing Stiffness ![]() 1.2?It is recognized that the classification of materials under Procedures A and B shall not hold in all cases. For example, some batt or blanket materials that have not been compression packaged will exhibit behavior more typical of Procedure A for their first loadings. Also, some higher density fibrous insulation boards that have been precompressed will exhibit load-deformation curves more typical of Procedure B. There will also be thermal insulations with load-deformation curves that follow none of the three types shown here; that is, curves with no straight-line portion, curves with compaction areas, and curves that change from negative to positive slope. 1.3?This test method does not cover reflective or loose fill insulations. 1.4?The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | 91.100.60 : 방열 및 방음 재료 |
페이지수 | 5 |
Edition | 23 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM C165-23 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2023-03-01 | 표준 |
2 | ASTM C165-23 REDLINE | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2023-03-01 | 표준 |
3 | ASTM C165-07(2017) | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2017-09-01 | 구판 |
4 | ASTM C165-07(2012) | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2012-09-01 | 구판 |
5 | ASTM C165-07 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2007-05-01 | 구판 |
6 | ASTM C165-05 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2005-05-01 | 구판 |
7 | ASTM C165-95 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2000-10-10 | 구판 |
8 | ASTM C165-00 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations | 2000-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASME B16.47-2020 - Large Diameter Steel Flanges: NPS 26 through NPS 60 Metric/Inch Standard 상세보기
ASME B16.5-2020 - Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard 상세보기
ASTM D579/D579M-15 - Standard Specification for Greige Woven Glass Fabrics 상세보기
ASTM B62-17 - Standard Specification for Composition Bronze or Ounce Metal Castings 상세보기
ASTM D2996-17 - Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기