관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Mineral Hydraulic Oils
| 분야 | 05.02 : 석유제품 및 윤활유 (Ⅱ) |
|---|---|
| 적용범위 | 1.1?This specification covers mineral and synthetic oils of the types API groups I, II, III, and IV used in hydraulic systems, where the performance requirements demand fluids with one of the following characteristics: 1.1.1?A refined base oil or synthetic base stock (Class HH), 1.1.2?A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors (Class HL), 1.1.3?A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors plus anti-wear characteristics (Class HM), 1.1.4?A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors, anti-wear characteristics, and increased viscosity index higher than 140 (Class HV), 1.1.5?A refined mineral base oil or synthetic base stock with rust and oxidation inhibitors plus anti-wear characteristics meeting a higher performance level than an HM fluid to address higher demanding hydraulic systems (Class HMHP), and 1.1.6?A refined mineral base oil with rust or synthetic base stock and oxidation inhibitors, anti-wear characteristics, and increased viscosity index higher than 140 meeting a higher performance level than an HV fluid to address higher demanding hydraulic systems (Class HVHP). 1.2?This specification defines the requirements of mineral oil-based or synthetic-based hydraulic fluids that are compatible with most existing machinery components when there is adequate maintenance. 1.3?This specification defines only new lubricating oils before they are installed in the hydraulic system. 1.4?This specification defines specific types of hydraulic oils. It does not include all hydraulic oils. Some oils that are not included may be satisfactory for certain hydraulic applications. Certain equipment or conditions of use may permit or require a wider or narrower range of characteristics than those described herein. 1.5?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5.1?Exception?In X1.3.9 on Wear Protection, the values of pump pressure are in MPa, and the psi follows in brackets as a reference point immediately recognized by a large part of the industry. 1.6?The following safety hazard caveat pertains to the test methods referenced in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 75.120 : 유압유 |
| 페이지수 | 15 |
| Edition | 23 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D6158-23 | Standard Specification for Mineral Hydraulic Oils | 2023-11-01 | 표준 |
| 2 | ASTM D6158-23 REDLINE | Standard Specification for Mineral Hydraulic Oils | 2023-11-01 | 표준 |
| 3 | ASTM D6158-18 | Standard Specification for Mineral Hydraulic Oils | 2018-10-01 | 구판 |
| 4 | ASTM D6158-18 REDLINE | Standard Specification for Mineral Hydraulic Oils | 2018-10-01 | 구판 |
| 5 | ASTM D6158-16 | Standard Specification for Mineral Hydraulic Oils | 2016-01-15 | 구판 |
| 6 | ASTM D6158-14 | Standard Specification for Mineral Hydraulic Oils | 2014-12-01 | 구판 |
| 7 | ASTM D6158-10 | Standard Specification for Mineral Hydraulic Oils | 2010-05-01 | 구판 |
| 8 | ASTM D6158-05 | Standard Specification for Mineral Hydraulic Oils | 2005-06-01 | 구판 |
| 9 | ASTM D6158-99 | Standard Specification for Mineral Hydraulic Oils | 1999-12-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D3359-23 - Standard Test Methods for Rating Adhesion by Tape Test 상세보기
ASTM D3163-01(2023) - Standard Test Method for Determining Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading 상세보기
ASTM D2344/D2344M-22 - Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates 상세보기
ASTM D638-22 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D3171-22 - Standard Test Methods for Constituent Content of Composite Materials 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
