관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation
| 분야 | |
|---|---|
| 적용범위 | 1.1 This practice2 covers a procedure for applying the eddy current method to detect discontinuities in ferromagnetic pipe and tubing (Note 1) where the article being examined is rendered substantially non-magnetic by the application of a concentrated, strong magnetic field in the region adjacent to the examining coil. Note 1: For convenience, the term tube or tubular product will hereafter be used to refer to both pipe and tubing. 1.2 The procedure is specifically applicable to eddy current testing methods using an encircling-coil assembly. However, eddy current techniques that employ either fixed or rotating probe-coil assemblies may be used to either enhance discontinuity sensitivity on the large diameter tubular products or to maximize the response received from a particular type of discontinuity. 1.3 This practice is intended for use on tubular products having outside diameters from approximately 1/4 to 10 in. (6.35 to 254.0 mm). These techniques have been used for smaller and larger sizes however, and may be specified upon contractual agreement between the purchaser and the supplier. 1.4 This practice does not establish acceptance criteria; they must be specified by the using party or parties. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 6 |
| Edition | 16 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E309-24 | Standard Practice for Eddy Current Examination of Steel Tubular Products | 2024-07-01 | 표준 |
| 2 | ASTM E309-24 REDLINE | Standard Practice for Eddy Current Examination of Steel Tubular Products | 2024-07-01 | 표준 |
| 3 | ASTM E309-16 | Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation | 2016-06-01 | 구판 |
| 4 | ASTM E309-16 REDLINE | Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation | 2016-06-01 | 구판 |
| 5 | ASTM E309-11 | Standard Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation | 2011-02-15 | 구판 |
| 6 | ASTM E309-95(2006) | Standard Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation | 2006-07-01 | 구판 |
| 7 | ASTM E309-95 | Standard Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation | 1995-10-10 | 구판 |
| 8 | ASTM E309-95(2001) | Standard Practice for Eddy-Current Examination of Steel Tubular Products Using Magnetic Saturation | 1995-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E426-16 REDLINE - Standard Practice for Electromagnetic (Eddy Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys 상세보기
ASTM E570-15e1 - Standard Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products 상세보기
ASTM E215-16 REDLINE - Standard Practice for Standardizing Equipment and Electromagnetic Examination of Seamless Aluminum-Alloy Tube 상세보기
ASTM E703-14 REDLINE - Standard Practice for Electromagnetic (Eddy Current) Sorting of Nonferrous Metals 상세보기
ASTM E1571-11(2016)e1 - Standard Practice for Electromagnetic Examination of Ferromagnetic Steel Wire Rope 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
