관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | |
---|---|
적용범위 | 1.1?This test method covers the evaluation of specific light-transmitting and wide-angle-light-scattering properties of planar sections of materials such as essentially transparent plastic. Two procedures are provided for the measurement of luminous transmittance and haze. Procedure A uses a hazemeter as described in Section 5 and Procedure B uses a spectrophotometer as described in Section 8. Material having a haze value greater than 30?% is considered diffusing and should be tested in accordance with Practice E2387. 1.2?The values stated in SI units are to be regarded as standard. Note 1:?For greater discrimination among materials that scatter a high percent of light within a narrow forward angle, such as is the case with abraded transparent plastics, adjust the hazemeter and perform measurements in accordance with Test Method D1044. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2:?This test method is not equivalent to ISO 13468-1 and ISO/DIS 14782. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | |
페이지수 | 7 |
Edition | 21 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D1003-21 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2021-05-01 | 표준 |
2 | ASTM D1003-21 REDLINE | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2021-05-01 | 표준 |
3 | ASTM D1003-13 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2013-11-15 | 구판 |
4 | ASTM D1003-13 REDLINE | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2013-11-15 | 구판 |
5 | ASTM D1003-11e1 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2011-04-15 | 구판 |
6 | ASTM D1003-11 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2011-04-15 | 구판 |
7 | ASTM D1003-07e1 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2007-11-01 | 구판 |
8 | ASTM D1003-07 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2007-11-01 | 구판 |
9 | ASTM D1003-00 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 2000-06-10 | 구판 |
10 | ASTM D1003-92 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics | 구판 |
관련상품이 존재하지 않습니다.
ISO 1463:2021 - Metallic and oxide coatings — Measurement of coating thickness — Microscopical method 상세보기
ISO 6259-2:2020 - Thermoplastics pipes — Determination of tensile properties — Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI) 상세보기
ISO 844:2021 - Rigid cellular plastics — Determination of compression properties 상세보기
ASTM E1711-20 REDLINE - Standard Guide for Measurement of Behavior During Fish Toxicity Tests 상세보기
ASTM D3359-17 REDLINE - Standard Test Methods for Rating Adhesion by Tape Test 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기