관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | ISO/TC 45/SC 2 : Testing and analysis |
---|---|
적용범위 | ISO 6133:2015 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics. The results are calculated by determining the median and range of peak values from a graphical plot of force versus time recorded during the test. A trace for an adhesion strength test or tear strength test can show few or many force peaks, depending on the material under investigation. The choice of the method of calculation depends on the number of peaks in the trace. The purpose of this International Standard is to obtain more uniformity in the evaluation and presentation of test results. It is applicable only, however, when specified in another International Standard, i.e. a method of test or a specification. For other details, such as apparatus, test piece preparation, conditioning, procedure, etc., requirements given in the relevant International Standard shall apply. NOTE In certain cases, the methods of analysis given might not be adequate, for example, for peak values showing a trend with time. In cases where the minimum force values are of interest, it is possible to use the same methods of calculation as when determining from a range of peak values. |
국제분류(ICS)코드 |
83.060 : 고무
83.080.01 : 플라스틱 일반 |
페이지수 | 5 |
Edition | 3 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ISO 6133:2015 | Rubber and plastics — Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength | 2015-08-13 | 표준 |
2 | ISO 6133:1998 | Rubber and plastics — Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength | 1998-02-26 | 구판 |
3 | ISO 6133:1981 | Rubber and plastics — Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength | 1981-04-01 | 구판 |
관련상품이 존재하지 않습니다.
KS M ISO 1795(2022 확인) - 천연 및 합성 원료 고무-시료 채취 및 처리 방법 상세보기
KS M ISO 5893 - 고무와 플라스틱 시험장치 — 인장, 굴곡 및 압축(일정한 이동속도) — 요구사항 상세보기
KS M ISO 18454 - 신발 — 신발의 구성재료 및 신발의 전처리와 시험을 위한 표준 대기 조건 상세보기
KS M ISO 188(2019 확인) - 가황 또는 열가소성 고무 — 촉진 노화 및 내열시험 상세보기
ISO 23529:2016 - Rubber — General procedures for preparing and conditioning test pieces for physical test methods 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기