관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 3: High-carbon cast-steel shot and grit
| 분야 | ISO/TC 35/SC 12 : Preparation of steel substrates before application of paints and related products |
|---|---|
| 적용범위 | This document specifies requirements for 14 grades of high-carbon cast-steel shot and 11 grades of high-carbon cast-steel grit, as supplied for blast-cleaning processes. Values are specified for hardness, density, defect/structural requirements and chemical composition. The requirements specified in this document apply to abrasives supplied in the "new" condition only. They do not apply to abrasives either during or after use. Test methods for metallic blast-cleaning abrasives are given in the various parts of ISO 11125. High-carbon cast-steel shot and grit are used in both static and site blasting equipment. They are most often selected where a facility exists for the recovery and re-use of the abrasive. NOTE 1 Information on commonly referenced national standards for metallic abrasives and their approximate relationship with ISO 11124 is given in Annex A. NOTE 2 Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504‑2. |
| 국제분류(ICS)코드 | 25.220.10 : 블라스팅 |
| 페이지수 | 9 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 11124-3:2018 | Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 3: High-carbon cast-steel shot and grit | 2018-09-07 | 표준 |
| 2 | ISO 11124-3:1993 | Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 3: High-carbon cast-steel shot and grit | 1993-12-02 | 구판 |
ISO/DIS 11124-6 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 6: Stainless steel (shot and irregulars) 상세보기
ISO/DIS 11124-7 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 7: High chromium white cast iron grit 상세보기
ISO 11124-4:2018 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 4: Low-carbon cast-steel shot 상세보기
ISO 11124-2:2018 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 2: Chilled-iron grit 상세보기
ISO 11124-1:2018 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 1: General introduction and classification 상세보기
DIN EN 1993-1-9:2010-12 - Eurocode 3: Design of steel structures - Part 1-9: Fatigue (includes Corrigendum AC:2009) 상세보기
DIN EN 1993-1-8:2010-12 - Eurocode 3: Design of steel structures - Part 1-8: Design of joints (includes Corrigendum AC:2009) 상세보기
DIN EN 1993-1-1/A1:2014-07 - Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings (includes Amendment 1:2014) 상세보기
DIN EN 1993-1-1:2010-12 - Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings (includes Corrigendum AC:2009) 상세보기
DIN EN 1990:2010-12 - Eurocode: Basis of structural design (includes Amendment A1:2005 + Corrigendum A1:2005/AC:2010) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
