해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ISO 6507-1:2023
Metallic materials — Vickers hardness test — Part 1: Test method- 발행일 : 2023-10-16
- 발행기관 : ISO
상세정보
분야 | ISO/TC 164/SC 3 : Hardness testing |
---|---|
적용범위 | This document specifies the Vickers hardness test method for the three different ranges of test force for metallic materials, including hard metals and other cemented carbides (see Table 1), metallic coatings and other inorganic coatings. The Vickers hardness test is specified in this document for lengths of indentation diagonals between 0,020 mm and 1,400 mm. Using this method to determine Vickers hardness from smaller indentations is outside the scope of this document as results would suffer from large uncertainties due to the limitations of optical measurement and imperfections in tip geometry. The Vickers hardness specified in this document is also applicable for metallic and other inorganic coatings including electrodeposited coatings, autocatalytic coatings, sprayed coatings and anodic coatings on aluminium. This document is applicable to measurements normal to the coated surface and to measurements on cross-sections, provided that the characteristics of the coating (smoothness, thickness, etc.) permit accurate readings of the diagonal of the indentation. This document is not applicable for coatings with thickness less than 0,030 mm when testing normal to the coating surface. This standard is not applicable for coatings with thickness less than 0,100 mm when testing a cross-section of the coating. ISO 14577-1 can be used for the determination of hardness from smaller indentations.” A periodic verification method is specified for routine checking of the testing machine in service by the user. For specific materials and/or products, relevant International Standards exist. |
국제분류(ICS)코드 | 77.040.10 : 금속의 기계적 시험 |
페이지수 | 35 |
Edition | 5 |
이력정보
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ISO 6507-1:2023상세보기 | Metallic materials — Vickers hardness test — Part 1: Test method | 2023-10-16 | 표준 |
2 | ISO 6507-1:2018상세보기 | Metallic materials — Vickers hardness test — Part 1: Test method | 2018-01-10 | 구판 |
3 | ISO 6507-1:2005상세보기 | Metallic materials — Vickers hardness test — Part 1: Test method | 2005-12-08 | 구판 |
4 | ISO 6507-1:1997상세보기 | Metallic materials — Vickers hardness test — Part 1: Test method | 1997-11-20 | 구판 |
5 | ISO 6507-1:1982상세보기 | Metallic materials — Hardness test — Vickers test — Part 1: HV 5 to HV 100 | 1982-07-01 | 구판 |
관련상품
- ISO 6507-2:2018 - Metallic materials — Vickers hardness test — Part 2: Verification and calibration of testing machines
- ISO 6507-3:2018 - Metallic materials — Vickers hardness test — Part 3: Calibration of reference blocks
- ISO 6507-4:2018 - Metallic materials — Vickers hardness test — Part 4: Tables of hardness values
다른 사람이 함께 구입한 상품
- ISO 6508-1:2023 - Metallic materials — Rockwell hardness test — Part 1: Test method
- ISO 6892-1:2019 - Metallic materials — Tensile testing — Part 1: Method of test at room temperature
- ISO 4136:2022 - Destructive tests on welds in metallic materials — Transverse tensile test
- ASTM E8/E8M-24 - Standard Test Methods for Tension Testing of Metallic Materials
- ASTM E23-24 - Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)