관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
초안
판매
Implants for surgery — Partial and total hip joint prostheses — Part 12: Deformation test method for press-fit acetabular components
| 분야 | ISO/TC 150/SC 4 : Bone and joint replacements |
|---|---|
| 적용범위 | This part of ISO 7206 specifies a test method for determining short-term deformation of a press-fit acetabular component for total hip joint replacement under specific laboratory conditions. It also defines the conditions of testing so that the important parameters that affect the components are taken into account and it describes how the specimen is set up for testing. The described method is intended to be used to measure the amount of deformation under load and plastic deformation after unloading of various designs and materials used for acetabular components in total hip joint replacement. These measurements are then used in an evaluation of risks associated with acetabular cup deformation for the acetabular component under evaluation to determine if its performance can be adversely affected. In the evaluation of risks associated with acetabular component deformation, it can be useful to take into consideration various design, material, and surgical implantation factors (for example, those identified in Clause 8), and, if necessary, a comparison of results to a reference implant tested under the same conditions. Depending on this evaluation, additional testing and/or clinical data, which is outside the scope of this document, can be necessary. The loading of the acetabular components in vivo will, in general, differ from the loading defined in this test method. The results obtained here cannot be used to directly predict in vivo performance. This part of ISO 7206 does not cover methods of examining the test specimens.
|
| 국제분류(ICS)코드 | 11.040.40 : 외과. 보철술. 교정술용 이식 |
| 페이지수 | 10 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 7206-12:2016 | Implants for surgery — Partial and total hip joint prostheses — Part 12: Deformation test method for acetabular shells | 2016-09-23 | 표준 |
| 2 | ISO/DIS 7206-12 | Implants for surgery — Partial and total hip joint prostheses — Part 12: Deformation test method for press-fit acetabular components | 초안 |
ISO/DIS 7206-8 - Implants for surgery — Partial and total hip joint prostheses — Part 8: Methods of determining endurance performance of stemmed femoral components 상세보기
ISO 7206-3:1988 - Implants for surgery — Partial and total hip joint prostheses — Part 3: Determination of endurance properties of stemmed femoral components without application of torsion 상세보기
ISO 7206-5:1992 - Implants for surgery — Partial and total hip joint prostheses — Part 5: Determination of resistance to static load of head and neck region of stemmed femoral components 상세보기
ISO 7206-7:1993 - Implants for surgery — Partial and total hip joint prostheses — Part 7: Endurance performance of stemmed femoral components without application of torsion 상세보기
ISO 7206-9:1994 - Implants for surgery — Partial and total hip joint prostheses — Part 9: Determination of resistance to torque of head fixation of stemmed femoral components 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
