관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens
| 분야 | ISO/TC 61/SC 13 : Composites and reinforcement fibres |
|---|---|
| 적용범위 | ISO 1268-10:2005 specifies the general principles to be followed while injection moulding test specimens of bulk moulding compound (BMC) and gives details of mould designs for preparing one type of specimen for use in establishing reproducible moulding conditions. Where appropriate, this part of ISO 1268 may be applied to sheet moulding compound (SMC) formulated for injection moulding. Its purpose is to promote uniformity in describing the main parameters of the moulding process and also to establish uniform practice in reporting moulding conditions. The particular conditions required for the reproducible preparation of test specimens which will give comparable results will vary for each material used. These conditions are given in the International Standard for the relevant material or are to be agreed upon between interested parties. |
| 국제분류(ICS)코드 | 83.120 : 강화 플라스틱 |
| 페이지수 | 16 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 1268-10:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens | 2005-02-04 | 표준 |
ISO 1268-3:2000 - Fibre-reinforced plastics — Methods of producing test plates — Part 3: Wet compression moulding 상세보기
ISO 1268-2:2001 - Fibre-reinforced plastics — Methods of producing test plates — Part 2: Contact and spray-up moulding 상세보기
ISO 1268-7:2001 - Fibre-reinforced plastics — Methods of producing test plates — Part 7: Resin transfer moulding 상세보기
ISO 1268-5:2001 - Fibre-reinforced plastics — Methods of producing test plates — Part 5: Filament winding 상세보기
ISO 1268-1:2001 - Fibre-reinforced plastics — Methods of producing test plates — Part 1: General conditions 상세보기
ISO 12686:1999 - Metallic and other inorganic coatings -- Automated controlled shot-peening of metallic articles prior to nickel, autocatalytic nickel or chromium plating, or as a final finish 상세보기
ISO 5725-5:1998 - Accuracy (trueness and precision) of measurement methods and results -- Part 5: Alternative methods for the determination of the precision of a standard measurement method 상세보기
DIN EN 13473-3:2001-11 - Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 3: Specific requirements; English version of DIN EN 13473-3 상세보기
DIN EN 13473-2:2001-11 - Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 2: Methods of test and general requirements; English version of DIN EN 13473-2 상세보기
DIN EN 13473-1:2001-11 - Reinforcement - Specifications for multi-axial multi-ply fabrics - Part 1: Designation; English version of DIN EN 13473-1 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
