관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Cylindrical gears — ISO system of flank tolerance classification — Part 2: Definitions and allowable values of double flank radial composite deviations
| 분야 | ISO/TC 60 : Gears |
|---|---|
| 적용범위 | This document establishes a gear tooth classification system relevant to double flank radial composite deviations of individual cylindrical involute gears and sector gears. It specifies the appropriate definitions of gear tooth deviations, the structure of the gear tooth flank classification system, and the allowable values of the gear tooth deviations. It provides formulae to calculate tolerances for individual product gears when mated in double flank contact with a master gear. Tolerance tables are not included. This document is applicable to gears with three or more teeth that have reference diameters of up to 600 mm. This document does not provide guidance on gear design nor does it recommend tolerances. |
| 국제분류(ICS)코드 | 21.200 : 기어류 |
| 페이지수 | 22 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 1328-2:2020 | Cylindrical gears — ISO system of flank tolerance classification — Part 2: Definitions and allowable values of double flank radial composite deviations | 2020-02-26 | 표준 |
| 2 | ISO 1328-2:1997 | Cylindrical gears -- ISO system of accuracy -- Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information | 1997-07-31 | 구판 |
ISO 1328-1:2013 - Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth 상세보기
ISO 1328-1:2013 - Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth 상세보기
ISO 6336-3:2019 - Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength 상세보기
ISO/TS 14521:2020 - Gears — Calculation of load capacity of worm gears 상세보기
ISO 6336-1:2019 - Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors 상세보기
ISO 6336-2:2019 - Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
