관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 4: Dynamic stiffness method
| 분야 | ISO/TC 108 : Mechanical vibration, shock and condition monitoring |
|---|---|
| 적용범위 | ISO 18437-4:2008 specifies a direct method for measuring the complex dynamic moduli of elasticity (the Young, shear and bulk moduli, and their respective loss factors corresponding to the tensile, shear and all compressive strains) for polymeric (rubbery and viscous polymers, as well as rigid plastics) materials over a wide frequency and temperature range. Measurements are performed by the dynamic stiffness method, which uses electric signals from sensors attached to a test piece. These signals are proportional to the dynamic forces acting on the test piece and the strains in the test piece due to the effect of these forces. The measurement frequency range is determined by the size of test piece, the accuracy required on the dynamic modulus measurements, the relationship between the stiffness of the oscillation generator and the stiffness of the test piece, and by the resonance characteristics of the test fixture used. The method presented in ISO 18437-4:2008 allows measurement under any static pre-load allowed for the test piece (including the test piece having the non-linear characteristics under different static loads), but under small dynamic (acoustic) strains, i.e. in limits where the linear properties of the test piece are not distorted. Depending on the pre-load conditions, the relation between the moduli is unique. |
| 국제분류(ICS)코드 | 17.160 : 진동. 충격 및 진동측정 |
| 페이지수 | 20 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 18437-4:2008 | Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 4: Dynamic stiffness method | 2008-05-20 | 표준 |
ISO 18437-2:2005 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 2: Resonance method 상세보기
ISO 18437-3:2005 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method 상세보기
ISO 18437-3:2005/Amd 1:2010 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method — Amendment 1 상세보기
ISO 18437-2:2005/Amd 1:2010 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 2: Resonance method — Amendment 1 상세보기
ISO 18437-5:2011 - Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 5: Poisson ratio based on comparison between measurements and finite element analysis 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
