관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement of gaseous and particulate exhaust emissions
| 분야 | ISO/TC 70/SC 8 : Exhaust gas emission measurement |
|---|---|
| 적용범위 | ISO 8178-1:2006 specifies the measurement and evaluation methods for gaseous and particulate exhaust emissions from reciprocating internal combustion (RIC) engines under steady-state conditions on a test bed, necessary for determining one weighted value for each exhaust gas pollutant. Various combinations of engine load and speed reflect different engine applications (see ISO 8178-4). ISO 8178-1:2006 is applicable to RIC engines for mobile, transportable and stationary use, excluding engines for motor vehicles primarily designed for road use. ISO 8178-1:2006 may be applied to engines used, for example, for earth-moving machines, generating sets and for other applications. In limited instances, the engine can be tested on the test bed in accordance with ISO 8178-2, the field test document. This can only occur with the agreement of the parties involved. It should be recognised that data obtained under these circumstances may not agree completely with previous or future data obtained under the auspices of ISO 8178-1:2006. Therefore, it is recommended that this option be exercised only with engines built in very limited quantities such as very large marine or generating set engines. For engines used in machinery covered by additional requirements (e.g. occupational health and safety regulations, regulations for powerplants), additional test conditions and special evaluation methods may apply. Where it is not possible to use a test bed or where information is required on the actual emissions produced by an in-service engine, the site test procedures and calculation methods specified in ISO 8178-2 are appropriate. |
| 국제분류(ICS)코드 |
27.020 : 내연기관
13.040.50 : 수송 배기가스 방사 |
| 페이지수 | 124 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 8178-1:2020 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement systems of gaseous and particulate emissions | 2020-06-24 | 표준 |
| 2 | ISO 8178-1:2017 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement systems of gaseous and particulate emissions | 2017-04-20 | 구판 |
| 3 | ISO 8178-1:2006 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement of gaseous and particulate exhaust emissions | 2006-09-14 | 구판 |
| 4 | ISO 8178-1:1996 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement of gaseous and particulate exhaust emissions | 1996-08-08 | 구판 |
ISO 8178-10:2002 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 10: Test cycles and test procedures for field measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions 상세보기
ISO 8178-11:2006 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 11: Test-bed measurement of gaseous and particulate exhaust emissions from engines used in nonroad mobile machinery under transient test conditions 상세보기
ISO 8178-7:2015 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 7: Engine family determination 상세보기
ISO 8178-8:2015 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 8: Engine group determination 상세보기
ISO 8178-6:2018 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 6: Report of measuring results and test 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
