관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | ISO/IEC JTC 1/SC 31 : Automatic identification and data capture techniques |
---|---|
적용범위 | This document is an engineering document intended for verifier manufacturers and application specification developers. This document describes modifications to the symbol quality methodology defined in ISO/IEC 15415 and a symbology specification. It defines alternative illumination conditions, some new terms and parameters, modifications to the measurement and subsequent grading of certain parameters and the reporting of the grading results. This document was developed to assess the symbol quality of direct marked parts, where the mark is applied directly to the surface of the item and the reading device is a two-dimensional imager. When application specifications allow, this method is also potentially applicable to symbols produced by other methods. This is appropriate when direct part marked (DPM) symbols and non-DPM symbols are being scanned in the same scanning environment. The symbol grade is reported as a DPM grade rather than as an ISO/IEC 15415 grade. |
국제분류(ICS)코드 | 35.040.50 : 자동인식 및 데이터 획득 자동화 |
페이지수 | 33 |
Edition | 1 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ISO/IEC 29158:2020 | Information technology — Automatic identification and data capture techniques — Direct Part Mark (DPM) Quality Guideline | 2020-12-14 | 표준 |
2 | ISO/IEC 29158:2020 | Information technology - Automatic identification and data capture techniques - Direct Part Mark (DPM) Quality Guideline | 2020-12-14 | 표준 |
3 | ISO/IEC TR 29158:2011 | Information technology - Automatic identification and data capture techniques - Direct Part Mark (DPM) Quality Guideline | 2011-10-06 | 폐지(대체) |
4 | ISO/IEC TR 29158:2011 | Information technology — Automatic identification and data capture techniques — Direct Part Mark (DPM) Quality Guideline | 2011-10-06 | 구판 |
5 | ISO/IEC DIS 29158 | Automatic identification and data capture techniques — Bar code symbol quality test specification — Direct Part Mark (DPM) | 초안 |
관련상품이 존재하지 않습니다.
ISO 14405-1:2016 - Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes 상세보기
ISO 14405-3:2016 - Geometrical product specifications (GPS) — Dimensional tolerancing — Part 3: Angular sizes 상세보기
ISO/IEC 16022:2006/Cor 2:2011 - Information technology — Automatic identification and data capture techniques — Data Matrix bar code symbology specification — Technical Corrigendum 2 상세보기
ISO/IEC 16022:2006/Cor 1:2008 - Information technology — Automatic identification and data capture techniques — Data Matrix bar code symbology specification — Technical Corrigendum 1 상세보기
ISO/IEC 16022:2006 - Information technology — Automatic identification and data capture techniques — Data Matrix bar code symbology specification 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기